Products / Flow Measurement
Ductus TT
Ultrasonic multipath flowmeter.
For pipes with a diameter of more than half a meter, acoustic flow measurement systems have long established themselves as a reliable and convenient measurement method. Measurements in several planes are a recommended method to determine the efficiency of the turbine without the need for calibration meeting the latest international standards. Fixed installed equipment form the basis for verifying the efficiency. A deterioration of efficiency can be detected right away and therefore corrections can be initiated at an early stage.
| Acoustic Paths: | 1 – 8 |
| Range: | ± 20 m/s |
| Display: | 4 lines, 20 characters |
| Datalogger: | internal, sampling interval user selectable |
| Communication: | RS-232, MODBUS, Ethernet, USB |
| Inputs: | max. 8 x 4-20 mA |
| Outputs: | max. 4 x 4-20 mA 2 x Relay, 2 x Pulse |
| Power Supply: | 85-264 VAC (50-60 Hz) or 12 VDC |
| Battery Backup: | integrated, 2 Ah |
| Enclosure: | Aluminium, wall mounted |
| Dimensions: | 400 x 500 x 160 mm (WxHxD) |
Feedthrough 45
Various transducers are available. Internal mount assemblies which can be fixed directly to the wall. The transducers are aligned by rotating them in their mounting into a predefined position and then fixed in place by tightening Feedtrough assemblies for installation through exposed penstock walls with access to the interior and exterior of the penstock flow meter section.
| Frequency: | 120 kHz |
| Beam Width: | 10° (-3dB) |
| Configuration: | IEC41 / ASMEPTC 18 |
| Pipe Diameter: | 0,3 m to 15 m |
| Pipe Wall Thickness: | up to 40 mm |
| Pressure Rate: | 60 bar – other ranges upon request |
| Material: | Stainless Steel |
| Cable: | twisted pair with shield |
| Cable Length: | max. 1000 m |
| Temperature Range: | -20° to 60°C |
| Installation: |
When pipe can be dewatered for installation. Designed to allow removal of the entire transducer for repair, replacement or cleaning without dewatering the pipe. |
Feedthrough 35
Various transducers are available. Internal mount assemblies which can be fixed directly to the wall. The transducers are aligned by rotating them in their mounting into a predefined position and then fixed in place by tightening Feedtrough assemblies for installation through exposed penstock walls with access to the interior and exterior of the penstock flow meter section.
| Frequency: | 120 kHz |
| Beam Width: | 10° (-3dB) |
| Configuration: | IEC41 / ASMEPTC 18 |
| Pipe Diameter: | 0,3 m to 15 m |
| Pipe Wall Thickness: | up to 40 mm |
| Pressure Rate: | 60 bar – other ranges upon request |
| Material: | Stainless Steel |
| Cable: | twisted pair with shield |
| Cable Length: | max. 1000 m |
| Temperature Range: | -20° to 60°C |
| Installation: |
When pipe can be dewatered for installation. Designed to allow removal of the entire transducer for repair, replacement or cleaning without dewatering the pipe. |
Transducer Internal Mount
| Frequency: | 200 kHz |
| Beam Width: | 18° (-3dB) |
| Configuration: | IEC41 / ASMEPTC 18 |
| Pipe Diameter: | min. 1000 mm |
| Pipe Wall Thickness: | – |
| Pressure Rate: | max. 100 bar |
| Material: | Stainless Steel / Polyamid |
| Cable: | twisted pair with shield |
| Cable Length: | max. 1000 m |
| Temperature Range: | -10° to 60°C |
| Installation: | From the inside |